Open safety recalls, the components owners report failing most often, crash-test results and running costs for the 2013 Ford Focus, assembled from NHTSA and EPA records.
Everything on this page applies to the model as a whole. Run its VIN to decode that exact car, its engine, trim, assembly plant and factory equipment, alongside these records.
Open a VIN recordRecalls and complaints are filed against a specific model year, so figures differ from one year to the next even within a single generation. See every Ford Focus year.
NHTSA lists 12 recalls for this make, model and year. Recalls apply to the model, so some may already be fixed on this specific car. A dealer can confirm from the VIN.
Issue: Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Risk: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Campaign 18V735000
Issue: Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Risk: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Campaign 19V515000
Issue: Ford Motor Company (Ford) is recalling certain model year 2012-2015 Ford Focus, 2013-2015 Ford Escape and Ford C-MAX, 2015 Lincoln MKC and Ford Mustang, and 2014-2016 Ford Transit Connect vehicles. A component within the door latches may break, preventing the doors from latching and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
Risk: A door that is not securely latched could open while the vehicle is in motion, increasing the risk of injury to a vehicle occupant.
Remedy: Ford will notify owners, and dealers will replace the door latches with an improved part, free of charge. The recall began on January 27, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S30.
Campaign 16V643000
Issue: Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Risk: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Campaign 16V698000
Issue: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM).
Risk: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the current crimped splices with new splices, free of charge. The recall began on January 7, 2016. Owners may contact Ford customer service 1-866-436-7332. Ford's number for this recall is 14S17-S1.
Campaign 15V813000
Issue: Ford Motor Company (Ford) is recalling certain model year 2013-2014 Escape vehicles manufactured October 5, 2011, to April 1, 2013, and equipped with 2.0 liter engines and Focus ST vehicles manufactured February 14, 2012, to October 14, 2013, and equipped with 2.0 liter engines. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM).
Risk: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the current crimped splices with new splices, free of charge. The recall began in October 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S17.
Campaign 14V495000
Issue: Ford is recalling certain model year 2012-2013 Focus BEV vehicles equipped with High Intensity Discharge (HID) headlights, manufactured September 15, 2011, through May 6, 2013; and model year 2013 Focus ST vehicles equipped with High Intensity Discharge (HID) headlights, manufactured February 16, 2012, through May 7, 2013. Due to a wiring incompatability, the front side marker lamps may not function. Thus, these vehicles fail to comply to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."
Risk: Without the proper illumination of the side maker lamps, the vehicle may be less visible in night time conditions, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will modify the headlamp assembly wiring, free of charge. The recall began on August 16, 2013. Owners may contact the Ford customer relationship center at 1-866-436-7332. Ford's recall number is 13C04.
Campaign 13V335000
Issue: This recall involves aftermarket parts sold by Yakima Products, Inc. for use on model year 2012 and 2013 Ford Focus vehicles. This recall is being conducted by Yakima, not by Ford. Certain combined Q-Tower and Q128 Clip rooftop rack systems, part numbers 8000124 and 8000728, do not fully contact the door frame.
Risk: Without proper contact of the rooftop rack clip to the door frame, there is insufficient clamping pressure and friction. The system may slide off the vehicle when loaded with accessories, possibly becoming a road hazard to other vehicles or causing injury to pedestrians.
Remedy: Yakima will notify owners, and Yakima or a Yakima dealer will refund the purchase of the Q-Tower and Q-128 Clip system. There is no replacement system available for the 2012-2013 model year Ford Focus. The safety recall began on October 15, 2012. Only vehicles equipped with the vehicle rack system are affected. This recall is being conducted by Yakima, not Ford. Owners may contact Yakima at 1-888-925-4621.
Campaign 12E035000
Issue: Ford is recalling certain model year 2013 Focus and C-Max vehicles built from November 16, 2012, through November 21, 2012; and model year 2013 Escape vehicles manufactured from November 14, 2012, through November 21, 2012. The left rear door child lock was built incorrectly. As a result, the child lock may not engage when the operator uses normal force to activate the child lock.
Risk: The operator may incorrectly believe the child lock is engaged. However, the door may be opened from the inside, increasing the risk of injury to an unrestrained child.
Remedy: Ford will notify owners, and dealers will inspect the affected rear door latches, and replace them as necessary, free of charge. The recall began on March 27, 2013. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Campaign 13V085000
Issue: Ford Motor Company (Ford) is recalling certain 2011-2014 Fiesta, 2013-2014 Fusion, 2015 Mustang, 2013-2015 Escape and C-Max, 2012-2015 Focus, 2014-2016 Transit Connect, 2013-2014 Lincoln MKZ, and 2015 MKC vehicles. These vehicles were previously recalled and repaired under recalls 15V-246, 16V-643 or 17V-210, however the repair may not have been completed properly. A component within the door latches may break making the doors difficult to latch and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
Risk: A door that is not securely latched could open while the vehicle is in motion, increasing the risk of injury to a vehicle occupant.
Remedy: Ford will notify owners, and dealers will inspect the latch date codes to confirm if the repair was done correctly, and replace the side door latches if necessary, free of charge. Owners will also have the option to inspect their own vehicle's door latches and enter the date codes into a website to determine if the latches are correct. Owner notification letters were mailed on July 27, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S30.
Campaign 20V331000
Issue: Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Risk: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Campaign 26V011000
Issue: Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Risk: An engine that stalls while driving increases the risk of a crash.
Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Campaign 26V369000
No EPA fuel-economy match for this model. Naming may differ, or it predates EPA records.
NHTSA frontal crash test
4 open NHTSA investigations into this model. Investigations come before recalls, so these are potential defects not yet covered by one.
Rated configuration: 2013 Ford Focus 4 DR FWD
The parts named most often across 2,110 owner complaints filed with NHTSA for this make, model and year.
4 crashes · 3 injured
5 crashes · 1 injured
1 fire
2 crashes · 3 fires · 2 injured · 1 death
1 fire · 1 injured
Complaints are self-reported and skew toward problems people find alarming, so read this as where to look rather than as a defect rate.
3 complaint-reported fatalities on this model.
RE: FAULTY THROTTLE WIRING / LOCATION CAUSING CORROSION 2013 FORD FOCUS - RECALL NEEDED To Whom It May Concern: My 2013 Ford Focus SE Flex with VIN [XXX] lost power while traveling from [XXX] to [XXX] a couple times before completely dying. My code reader was getting fixed throttle codes 2112, 2111 and pending codes 122, 223. I switched out the throttle body AND accelerator pedal position sensor. This did NOT resolve the issue. I had the Focus towed to Downey Ford in [XXX] where they found a Technical Service Bulletin stating endless Focuses had this issue with corroded wiring, which appears to be caused by TSB 15-0036, which is regarding the wiring harness rubbing against a sharp part of the intake, which can cause shorts in the cables. This Ford Dealership repair cost me $845.80 + grief + an extended stay at my hospitable parents in [XXX]. This concern should be escalated to RECALL status as it leaves your loyal customers stranded on the roadside. My request is a full refund from Ford for $845.80 CAD. See Downey Ford Invoice # SO # XXX attached. Source: [XXX] [XXX]: Bear with me, this is going to be a bit long. TL;DR: Car will not accelerate, CEL/MTC states problem with "accelerator pedal position sensor". Wiring harness has been cut into by rubbing on intake. I want to splice it to fix it, but need advice due to length/resistance requirements. Two weeks ago, my wife was driving my 2013 Ford Focus SE Hatchback and right as she got off the freeway, it instantly lost power, a message appeared on the screen stating "Engine Fault - Repair Now", and it idled super rough. She restarted the engine and it was fine until she tried accelerating more than a tiny bit, at which point the same symptoms occurred again. She was able to limp the car home. Having misplaced my OBD2 scanner, I limped it over to the local auto parts store and they read the code as INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I purchased a 2013 Ford Focus from Boucher Ford of Menomonee Falls, WI in February, 2026. A few months later, Ford issued a recall on this car that requires the Powertrain Control Module to be reprogrammed to avoid issues like a collapsed fuel tank or stalling while driving, potentially causing an accident. I had been informed by a mechanic that this car was sold to me with a custom tune on the PCM. This tune was not disclosed to me when I purchased the car and due to the PCM being modified, the recall cannot be performed without damage to the PCM rendering the car undriveable. I tried working with Jeff Samp (General Manager) at the dealership but he told me they were not required by law to check for tunes when a car is traded in and that he could have someone "look at the car" but if they damage the PCM performing the recall, they will not be held responsible. I opened a case with Ford Motor Company and was informed that they would escalate to some kind of dealership oversight department and that it might take a couple weeks to get a response. I never received a response so I called Ford to inquire and was told that they are not sure why I was told that, that no such department exists, and that all they can do is call the dealership on my behalf and "ask" them to deal with it. Facts: 1. They sold me a car with a modified Powertrain Control Module which can affect many things, even falsely disabling check engine lights. 2. A FEDERAL RECALL for my own safety cannot be performed on this vehicle IN THE CONDITION THEY SOLD IT TO ME, putting my safety, my passengers' safety, and the safety of other motorists at risk. 3. Boucher Ford will not remedy this issue or even contact the previous owner as I requested to find out what kind of tune is on this vehicle so that I can get it removed and this safety recall performed. I want the PCM replaced with a new unit, with the new software that complies with this recall.
The contact owns a 2013 Ford Focus. The contact stated that the transmission failed, and the vehicle lost motive power, and the vehicle was stuck in the middle of traffic. The contact referenced several satisfaction programs for the issue; however, the VIN was not included in the repair. The vehicle was towed back to the residence due to it not being able to operate. The contact stated there was an unknown warning light on the instrument panel. The contact stated that the transmission had overheated. The manufacturer was notified of the failure. The vehicle was taken to an independent mechanic, and it was confirmed with transmission failure.
Issue happened in November 2016. The glass sunroof exploded while driving NE on I-44 just SW of Springfield MO. The reason I am reporting this now, is that I saw a news article about this happening often. Until I saw the news article I thought it was a one of event. We did not witness anything hitting the car/sunroof. I don't expect anything from this report. I just wanted report that a Ford Focus experienced this type of event.
See attached document for complaint.
I am reporting a severe vehicle safety hazard and engine stalling incident on my 2013 Ford Focus caused by an un-remedied factory emissions safety defect (related to Ford Recall 26S40 / 18S32). Due to an incomplete factory software monitoring patch, the canister purge valve stuck open and allowed continuous, unchecked engine vacuum to pull straight out of the plastic fuel tank. This heavy vacuum physically collapsed and deformed the bottom of the plastic fuel tank inward by approximately 0.25 to 0.375 inches. This structural collapse compressed the internal fuel pump assembly and mechanical float arm, falsifying the dashboard fuel gauge and distance-to-empty calculations. On April 2nd, while driving on Interstate 95 at midnight, the vehicle displayed an inaccurate fuel level, ran completely dry, and suffered a sudden engine stall in high-speed traffic without warning. My family and I were trapped in a highly hazardous situation and were forced to physically push the disabled vehicle 3 miles down the highway in total darkness. We ultimately had to enlist the emergency intervention of the Florida State Patrol Road Rangers to dispatch a unit and supply fuel so we could safely clear the interstate. The vehicle has since thrown a hard diagnostic trouble code P0443, confirming a complete electrical circuit malfunction of the EVAP system. Ford's failure to successfully deploy a functional software monitor has caused severe structural damage to my fuel system and created an imminent, life-threatening safety risk to my family on public highways. I am requesting a federal record of this incident to compel a full vehicle inspection and complete fuel system component replacement by the manufacturer."
The evap canister purge valve has been a recurring problem for this vehicle. The canister was replaced in 2021, but continued having problems, as it pulled a vacuum on the fuel tank in upwards of 3/8 inch. (Documented by Murray Ford in 2023 and reassuredthere was no issue by them) the vehicle has displayed inaccurate fuel readings and caused our family to be disabled and then stranded in the night on highway 95. It put the safety of my family, and other motorists at risk The problem hasn't been duplicated because their "software fix" essentially ignored the problem altogether. There were no warnings. According to my vehicle it had at least 50 miles til empty. The fuel sending unit is displaying innacurqte fuel readings, and the fuel pump has displayed symptoms, characterized by surging, stalled when accelerating from a stop, and of course, completely shutting off, while on the highway. I've tried my best to trust and be patient with Ford and for them to do the right thing, but have been brushed off.
I had my purge valve replaced under 24N07 ford costumer satisfactory program and the faulty purge valve damaged my catalytic converter and caused my engine light to illuminate with P0420.
Transmission problems and my car is still under 100000 and it’s a 2013 ford focus
While driving home from work, I was attempting to accelerate my RPMs showed 4000. However, my speed did not match the car. He hesitated and was doing a lot of jerking after I got home turned off the car turned it back on my check engine light came on and it threw a code P07A5.
The "shift tower" typically refers to the external mechanism on top of the transmission where the shifter cables connect. Problems with this part, which is a broken internal pin, result in a shifter that moves freely without engaging any gears. The gear become in operatable when driving down the highway, which is a hazard on the road. There were no warning light just not ale to change gears.
The vehicle began to experience issues where it was difficult to start and ran rough. Multiple times after turning off vehicle and attempting to restart later it would not restart. Had vehicle towed to dealership for repairs, they conducted a recall repair and test over multiple days. Picked up vehicle, drove approximately 7 miles. Went into store came back and vehicle would not start. Multiple other recalls are listed for this date range and motor that likely could be impacting my current vehicle. However, this VIN is not listed as a specific recall. Current situation places driver and passenger at risk as the vehicle does not run properly and does not restart
Showing 12 of 2,110 complaints.